InfoWorks ICM

Showing 539 of 1338

Ability to change appearance of snapping 'cross-hairs'

When drawing subcatchments, you normally need quite a few layers showing - the modelled sewer network, a shapefile showing smaller private laterals, the DTM, OSMM. The snapping mode 'cross-hairs' can often get lost in the mix of colours, especiall...

Jason Kulsdom about 2 years ago in InfoWorks ICM / Productivity 0 Gathering support

2 VOTE

Infiltration surface in InfoWorks ICM

Within a part/selection of conduits, I want to know what the (infiltration) surface area is below a certain level (m AD). For example, what is the surface area of the ditch (bottom and sidewalls) up to a level of e.g., 4.0 or 5.0 m AD. Using Model...

Guest over 1 year ago in InfoWorks ICM / Other 0 Gathering support

2 VOTE

Enable resolution setting when view is stored in clipboard or files

When simulation results are summarized and reported, network data is printed after nicely arranged. In ICM, there is no way to define the resolution of views and it can deteriorate the printed views when they are output in large papers. Could you ...

Miyuki Okuda over 1 year ago in InfoWorks ICM / Printing 0 Gathering support

8 VOTE

The ability to save databases/models as previous versions for backwards compatibility

A few of our clients use different versions of InfoWorks for various reasons (some are resistant to upgrading until they've had a chance to vet the new versions and understand the changes in house). This can create a problem where we must maintain...

Dave White over 5 years ago in InfoWorks ICM / Data Exchange 1 Gathering support

7 VOTE

Add node level (hydraulic grade line) data to custom graphs for calibration

Allow for the ability to compare observed and predicted level data (or hydraulic grade lines) at nodes. Instead of depth in the pipe, I typically have water surface elevations at a node, specifically for treatment plant hydraulic modeling.

Guest almost 5 years ago in InfoWorks ICM / Calibration / Labels / Results 0 Gathering support

7 VOTE

Increased number of user pollutants

We would like to be able to trace pollutant sources through our 2D model. The way to do this would be to use the user defined pollutants . But... at the moment there are only four pollutants and potentially we'd have many different sources that we...

Richard Body almost 5 years ago in InfoWorks ICM / Pollutants / Water Quality 1 Gathering support

4 VOTE

ICM - HEC-22 Combination Inlet for continuous grade inlets

Currently ICM has 6 FWHA Gully Inlet types: ContCo Continuous Curb Opening ContG Continuous Grate SagC Sag Combination SagCO Sag Curb Opening SagG Sag Grate and UPC Grate A commonly used Inlet type (particularly in QLD Australia) that is missing ...

Guest almost 3 years ago in InfoWorks ICM / Hydraulics 0 Gathering support

3 VOTE

Options to export the statistics block of Graph template/Custom Graph

At the moment, from many cases one can export whole time series of flow/depth etc... then have to calculate the cumulative volume or max flow...despite that statistics are visible in the graph. Allow an option to export the statistics alongside ti...

Guest about 2 years ago in InfoWorks ICM / Export Data 0 Gathering support

7 VOTE

Infoworks ICM - Contours and Labels

Infoworks - ICM Contours with labels to be shown on ground model

Guest over 5 years ago in InfoWorks ICM / Terrain 1 Gathering support

5 VOTE

Correct calculation of volume within storage node when using porosity

Currently when a porosity value is applied to a storage node, the porosity is only applied for storage array entries which are below ground level. Storage array entries above ground level are assumed to have a porosity of 100%. Between the highest...

Lizzie almost 4 years ago in InfoWorks ICM / Hydraulics 1 Gathering support

Please enter your email address

FILTER BY CATEGORY