InfoWorks ICM

Showing 440

Include a Rainfall Generator Using Environment Canada Data

Similar to the ARR and NOAA 14 storm generators, build one that could utilize Environment Canada data with common distribution types.

Guest over 3 years ago in InfoWorks ICM / Rainfall 1 Gathering support

6 VOTE

Allow all objects (nodes, subcatchments etc) to be included within the ‘gauge’ objects used in the run window

In a simulation run window the user has the choice to use a selection list of 'gauged' objects. This is useful so as to provide the results of some objects more frequently, or to only save the results from some objects and not others, in order to ...

Lizzie over 3 years ago in InfoWorks ICM / Hydraulics 0 Gathering support

8 VOTE

I want Long-Sections of a pipe to show the unconnected pipes which cross

On a Long-Section of a pipe, I would like ICM to show the unconnected pipes which cross that long-section. This would illustrate potential pipe clashes. I imagine the unconnected pipes would be shown as circles on the long-section similar to how...

Guest over 4 years ago in InfoWorks ICM / Long Section / Profile 3 Gathering support

9 VOTE

leave Layers and Themes window open

Could you make it possible to work in the Geoplan without having to close the Layers and Themes window? It would make switching Layers on and off much easier. Alternatively you could add a separate window to switch layers on and off.

Guest about 5 years ago in InfoWorks ICM / Productivity / Visualization 1 Gathering support

3 VOTE

Ability to change appearance of snapping 'cross-hairs'

When drawing subcatchments, you normally need quite a few layers showing - the modelled sewer network, a shapefile showing smaller private laterals, the DTM, OSMM. The snapping mode 'cross-hairs' can often get lost in the mix of colours, especiall...

Jason Kulsdom over 1 year ago in InfoWorks ICM / Productivity 0 Gathering support

2 VOTE

Implement the Inflow Time Series Scaling Factor in InfoWorks from ICM SWMM

Scale Factor In ICM SWMM or SWMM5 a multiplier is used to adjust the values of the constituent's inflow time series. The scale factor can have several uses, such as allowing one to easily change the magnitude of an inflow hydrograph while keeping ...

Robert Dickinson about 1 year ago in InfoWorks ICM / Flow 0 Gathering support

8 VOTE

Speed up interfaces with 2D zones with millions of elements (make it a multicore process)

The interface for large 1D-2D models is very slow. While moving through the geoplan every time it takes about ten seconds to load and show the location. We noticed that in this time only 1 of the 32 CPU is used for 100%. We tried 2 complete differ...

Guest over 4 years ago in InfoWorks ICM / Performance 1 Gathering support

4 VOTE

Need additional Timestep function for "Between episodes" of "Simulation runoff only"

It needs creating a new Timestep function in ICM Run window that allows setting up timestep for "Simulation runoff only" for the "Between episodes" separately with "Timestep (s)" in Run window. This new function saves a lot of running time when th...

Guest over 2 years ago in InfoWorks ICM / Events / Simulations 0 Gathering support

7 VOTE

Show water levels at Bridge Linear Structures

We would like to see the water levels at the bridge linear structures as it is important for us to be able to see the water levels with respect to the bridge openings and decks.

Richard Body about 4 years ago in InfoWorks ICM / Bridge / Hydraulics / Results 0 Gathering support

5 VOTE

adjustments to a selected set of scenario's

In my opinion it would be very useful if you could make the same adjustments in one stretch for a selected set of scenario's. Similar to an adjustement you make in the base scenario that effects all the underlaying scenario's but than for a specif...

Guest almost 3 years ago in InfoWorks ICM / Scenario 1 Gathering support

Please enter your email address

FILTER BY CATEGORY