Ideas

Showing 158 of 1370

Calculation of Pump Power in ICM

A pump curve and energy/efficiency curve can be input into the software however there is no way to output the energy used by the pump. South Gippsland Water were keen on understanding whether ICM could do this to report their energy efficiency bas...

Ann Pugh almost 5 years ago in InfoWorks ICM / Pumps 0 Gathering support

2 VOTE

Allow Theming Inflow areas by attributes

I would like to visually theme the Inflow areas by an attribute, say, Percent Impervious (PIMP)

Guest over 3 years ago in InfoWorks ICM / Theme / Visualization 0 Gathering support

1 VOTE

Varying conduit/culvert shape along its length

When modelling irregular culverts, the shape of culvert usually varies along its length as well. EX: Culvert having 900mm dia at inlet, varies along its length and at outlet has 500mm. Can this be included in the options for transition of shape al...

Guest almost 2 years ago in InfoWorks ICM / River Modeling 1 Gathering support

2 VOTE

Visibility by system type

It would be usefull to have the possibility to easily switch on and off the layers of different system types by ticking on and of the different types/layers in the Geoplan Layers and Themes. By using the themes and adding visibility it is possib...

Richard Wilbrink over 3 years ago in InfoWorks ICM / GIS Layers 3 Gathering support

2 VOTE

Theme mapping for rain gauges boundary lines generated using Thiessen polygons method

Boundary lines generated with the Thiessen Polygon methodology to define the boundaries for different rain gauges are too thin when they are automatically generated inside ICM. This make them quite difficult to see when a model is loaded with many...

Guest over 3 years ago in InfoWorks ICM / Rainfall / Theme / Visualization 0 Gathering support

3 VOTE

I would like the option to model pump station that operate using VFDs.

I would like to be able to enter the full and reduced speed pump curves for each pump station that is controlled by variable frequency drives. In addition, I would need the set point or control that causes the pumps to ramp up to full speed.

Guest over 5 years ago in InfoWorks ICM / Pumps 0 Gathering support

3 VOTE

Optional channel to river reachs option

The way ICM identifies the centre-line of the river reach is by using the point with the lowest invert level. Regardless of the shape of the channels of how much is the value of the X coordinate, didn't affect the appearance of the section to gene...

Liu Qiusheng over 5 years ago in InfoWorks ICM / Network / River Modeling 0 Gathering support

3 VOTE

Auto-space custom labels

We use custom labels a lot in reporting how we model ancillaries, and for complex assets spend a long time adjusting labels so they don't overlap and do show up properly. It would be great if a more "smart" label engine could be used so that label...

Oliver Perkins over 5 years ago in InfoWorks ICM / Labels / Visualization 0 Gathering support

3 VOTE

Intelligently select nodes in river reaches

When clicking on a node over a subcatchment, the software can recognise the user is after the node. When the same is done for a node on a river reach, the node is not automatically selected but rather the choice is presented to the user.

Guest almost 6 years ago in InfoWorks ICM / Productivity / River Modeling 0 Gathering support

1 VOTE

Add the Detailed EPASWMM LID Detailed Report file for ICM InfoWorks and SWMM Networks

Both ICM SWMM and ICM InfoWorks incorporate the EPASWMM's Low Impact Development (LID) or Sustainable Drainage Systems (SuDS) controls and Subcatchment features, offering a summary of LID inputs and outputs within the SWMM5 Report File (RPT file)....

Robert Dickinson about 2 years ago in InfoWorks ICM / SUDS 0 Gathering support

Please enter your email address

FILTER BY CATEGORY