Hydraulics

Showing 95

Revision to manhole representation

ICM's default representation of manholes could be more accurate. The limitations of current setup allows accurate representation of either the shaft or the benching but not both. Thus most people tend to apply chamber areas to invert which overest...

Guest about 3 years ago in InfoWorks ICM / Hydraulics 0 Gathering support

4 VOTE

Improvement on the Numerical Correction Process in ICM

The current procedure for ‘Numerical Correction’ in ICM requires users to remove any existing values to calculate the correction (for Preismann and Base flow) before the inbuilt routine is run. If this wasn't made the calculated correction values ...

Guest about 5 years ago in InfoWorks ICM / Hydraulics 1 Gathering support

1 VOTE

Add the Detailed EPASWMM LID Detailed Report file for ICM InfoWorks and SWMM Networks

Both ICM SWMM and ICM InfoWorks incorporate the EPASWMM's Low Impact Development (LID) or Sustainable Drainage Systems (SuDS) controls and Subcatchment features, offering a summary of LID inputs and outputs within the SWMM5 Report File (RPT file)....

Robert Dickinson over 1 year ago in InfoWorks ICM / SUDS 0 Gathering support

3 VOTE

Calculation of Pump Power in ICM

A pump curve and energy/efficiency curve can be input into the software however there is no way to output the energy used by the pump. South Gippsland Water were keen on understanding whether ICM could do this to report their energy efficiency bas...

Ann Pugh about 4 years ago in InfoWorks ICM / Pumps 0 Gathering support

1 VOTE

Allow Ctrl+C and Ctrl+V in RTC dialogue (plus other RTC dialogue changes)

For no apparent reason, Ctrl+C and Ctrl+V do not work in the RTC dialogue - right-click-copy and right-click-paste still work though, which is confusing. Overall this issue (amongst others) contributes to the RTC dialogue feeling very clunky to us...

Jason Kulsdom over 1 year ago in InfoWorks ICM / RTC 1 Gathering support

3 VOTE

I would like the option to model pump station that operate using VFDs.

I would like to be able to enter the full and reduced speed pump curves for each pump station that is controlled by variable frequency drives. In addition, I would need the set point or control that causes the pumps to ramp up to full speed.

Guest almost 5 years ago in InfoWorks ICM / Pumps 0 Gathering support

3 VOTE

Optional channel to river reachs option

The way ICM identifies the centre-line of the river reach is by using the point with the lowest invert level. Regardless of the shape of the channels of how much is the value of the X coordinate, didn't affect the appearance of the section to gene...

Liu Qiusheng almost 5 years ago in InfoWorks ICM / Network / River Modeling 0 Gathering support

3 VOTE

Intelligently select nodes in river reaches

When clicking on a node over a subcatchment, the software can recognise the user is after the node. When the same is done for a node on a river reach, the node is not automatically selected but rather the choice is presented to the user.

Guest about 5 years ago in InfoWorks ICM / Productivity / River Modeling 0 Gathering support

1 VOTE

split network results lines

it would be great if the "splitting lines" function can be applied to network results lines too, which would help a lot if we need to break up a large amount of NRLs into multiple segments rather than redrawing them.

Guest almost 2 years ago in InfoWorks ICM / Hydraulics / Results 0 Gathering support

2 VOTE

Change Variable Speed Pumps Image

The image for Variable Speed Pumps under the "Other Special Diversion Examples" section is likely wrong. Looks like it is a copy of the image for Pump discharge pipes. Would be great if you could update with the right image! Thanks

Guest almost 4 years ago in InfoWorks ICM / Pumps 0 Gathering support

Please enter your email address

FILTER BY CATEGORY